The Provisioning state field in the Service Provider section of the output will change from NotProvisioned to Provisioned when the circuit is ready. To verify the provisioning state of a circuit, run the following PowerShell command: Get-AzExpressRouteCircuit -Name > -ResourceGroupName > Wait for the provider to provision the circuit. Send the ServiceKey for the new circuit to the service provider. Run the following PowerShell command: New-AzExpressRouteCircuit -Name > -ResourceGroupName > -Location > -SkuTier > -SkuFamily > -ServiceProviderName > -PeeringLocation > -BandwidthInMbps > For more information about this process, see ExpressRoute workflows for circuit provisioning and circuit states.Ĭreate an ExpressRoute circuit as follows: If you haven't already done so, add a subnet named GatewaySubnet to your Azure VNet and create an ExpressRoute virtual network gateway using the Azure VPN gateway service. ExpressRoute circuitĮnsure that your organization has met the ExpressRoute prerequisite requirements for connecting to Azure. WAN providers typically offer managed layer 3 connectivity.įor more information about connectivity providers, see the ExpressRoute introduction. Azure can be interconnected to your WAN to make it look just like any other branch office. Internet protocol virtual private network (IPVPN) providers (typically a multiprotocol label switching VPN) offer any-to-any connectivity between your branch offices and datacenters. You can integrate your wide area network (WAN) with Azure. Point-to-point Ethernet providers can offer layer 2 connections, or managed layer 3 connections between your site and Azure. You can connect your on-premises datacenters/offices to Azure through point-to-point Ethernet links. Co-location providers can offer either layer 2 cross-connections, or managed layer 3 cross-connections between your infrastructure in the co-location facility and Azure. If you're co-located in a facility with a cloud exchange, you can order virtual cross-connections to Azure through the co-location provider's Ethernet exchange. To get a list of connectivity providers available at your location, use the following Azure PowerShell command: Get-AzExpressRouteServiceProviderĮxpressRoute connectivity providers connect your datacenter to Microsoft in the following ways: Select a suitable ExpressRoute connectivity provider for your location. Follow these recommendations unless you have a specific requirement that overrides them. The following recommendations apply for most scenarios. Companies that provide a connection either using layer 2 or layer 3 connectivity between your datacenter and an Azure datacenter. You can also connect directly to Microsoft CRM Online through Microsoft peering.Ĭonnectivity providers (not shown). Connections are performed using Microsoft peering, with addresses that are either owned by your organization or supplied by your connectivity provider. The publicly available Microsoft 365 applications and services provided by Microsoft. These services are also available over the Internet, but accessing them using an ExpressRoute circuit provides low latency and more predictable performance, because traffic does not go through the Internet.
Azure services that can be used within a hybrid application. Application tiers can be segmented using subnets in each VNet.Īzure public services. Each VNet resides in a single Azure region, and can host multiple application tiers. Depending on how your connection is provisioned, you may need to provide the public IP addresses used by the routers.Īzure virtual networks (VNets). These routers enable a connectivity provider to connect their circuits directly to their datacenter. Two routers in an active-active highly available configuration. Depending on how your connection is provisioned, you may need to provide the public IP addresses used by the routers. Routers that connect the on-premises network to the circuit managed by the provider. The circuit uses the hardware infrastructure managed by the connectivity provider. A layer 2 or layer 3 circuit supplied by the connectivity provider that joins the on-premises network with Azure through the edge routers. A private local-area network running within an organization.ĮxpressRoute circuit. The architecture consists of the following components. Architectureĭownload a Visio file of this architecture. The private connection extends your on-premises network into Azure. ExpressRoute connections use a private, dedicated connection through a third-party connectivity provider.
OUTLOOK MAIL SERVER SETTINGS CKT.NET HOW TO
This reference architecture shows how to connect an on-premises network to virtual networks on Azure, using Azure ExpressRoute.
0 kommentar(er)
